• <strong id="n7php"></strong>

    <ruby id="n7php"></ruby>
      <i id="n7php"></i>
    1. <font id="n7php"></font>

      產品中心

      PRODUCTS

      壓敏電阻

      NTC熱敏電阻

      薄膜電容

      陶瓷電容

      溫度傳感器

      電容器可靠性測試


      t1.jpg



      項目


      性能要求

      試驗方法

      耐電壓(TV)

      兩引線間

      無擊穿或飛弧

      兩引線間施加50/60H  Y1:4000VAC/ 60秒 Y2:2500VAC/60秒;最大泄露電流50 mA

      引線與外表

       將電容器的兩條引線連接在一起,本體部分插入裝有小金屬球容器內(金屬球與引線間的距離不小于1.5mm),在金屬球與引線之間施加50/60Hz (Y1:4000VAC/60秒;Y2:2500VAC/60秒)

      絕緣阻抗(I.R.))

      ≥10000MΩ

      將電容器兩引線間施加500VD,充電時間60±5秒

      靜電容量和誤差
           (CAP&Tolerance)

      規定的容量和誤差范圍內

      測試頻率:1±0.2KHz   測試電壓: 1.0±0.2    Vrms (20±2℃)

      損耗角正切(tgδ)

      ≤250×10-4

      測試條件與靜電容量相同


      Item

      Performance

      Test  Method

      Withstand    Voltage(TV)

       

      Between    Terminals

      Should be    no remarkable and abnormality

      Apply    Y1:4000VAC;Y2:2500VAC/60sec ;charge/discharge current should not exceed 50A

      Between    Terminials and Encloser

      Insert the    capacitor body filled with a diameter of 1 mm metal ball in the container,but    keep away from the end of 2mm ontology is not inserted;Test voltage applied    between the short circuit loop terminal and a metal ball

      Insulation
                      Resistance(I.R.)

      ≥10000MΩ

      Applied    5OOVDC between two terminals ,duration:5 second

      Capacitance
      (C)&    Tolerance

      W it hi n the    specified tolerance

      Measuring    Frequency:1±0.2KHz
      Measuring    voltage: 1.0±0.2    Vrms (20±2℃)

      Dissipation Factor    (DF)

      ≤250×10-4

      Method    same with Capacitance



      t2.jpg


      項    目

      性能要求

      試驗方法

      引線引出端強度

      拉力

      符合電性能規定,引線無斷裂或松落
                     

      將電容器其中一根引線于徑向方向施加下列荷重(參照IEC-68-2-20):荷重1K g;時間10±1.0秒

      彎曲

      將電容器其中一根引線于徑向方向施加0.5K g荷重施加兩個循環; 每個循環引線于兩端子間彎曲90o,復位2~3秒;然后向相反方向彎曲90o復位

      Item

      Performance

      Test     Method

      Terminal  strength

      Tensile

      Should satisy electrical    characteristics;the terminals should be not break or loose

      Apply one lead the    specified strength(Refer to IEC-68-2-20):Load 1Kg; Duration:10±1.0Sec

      Bending

      Apply    one lead the 0.5Kg for two cycles;Each cycle     includes:90o once,Return to its initial position for 2~3 Sec,and then to the opposite direction    once

       

      t3.jpg


      項目

      性能要求

      試驗方法

      可焊性

      外觀

      均勻覆蓋引線浸入部分95%以上

      焊錫溫度:235±5℃  浸入時間: 2.5±0.5S
           浸入速度: 25±6mm/s

      耐焊接熱

      外觀

      無可見的損傷或異常

      預熱溫度:100~120℃
           預熱時間:60秒內
           溫度上升率不超過2 ℃/秒
           焊錫溫度260±5℃, 浸入時間10±0.5Sec.
           浸錫深度:引線根部起4±0.8mm
           試驗后處理:電容器置于標準大氣壓條件下放置24±2小時后再進行測量

      容量變化率

      ±10%    (Y5P)
           ±15%(Y5U )
           ±20%(Y5V )

      耐電壓
           (引線之間)

      符合耐電壓規定

      損耗角正切

      ≤250×10-4   (1±0.2KHz,1.0±0.2 Vrms,20±2℃)

      絕緣阻抗

      ≥5000 MΩ(500V60秒,20±2℃)

       濕熱試驗

      外觀

      無可見的損傷或異常

      溫度:40±2℃
           濕度:90~95%
           存放時間:500+24小時。
           試驗后處理:電容器置于標準大氣壓條件下放置1~2小時后再進行測量

      容量變化率

      ±10%    (Y5P)
           ±15%(Y5U )
           ±20%(Y5V )

      耐電壓
           (引線之間)

      符合耐電壓規定

      損耗角正切

      ≤5.0×10-4  (Y5P、Y5U)
           ≤7.5×10-4    (Y5V)
           (1±0.2KHz,1.0±0.2 Vrms,20±2℃)

      絕緣阻抗

      ≥5000 MΩ(500V60秒,20±2℃)

      Item

      Performance

      Test     Method

      Solderability

      Apperance

      Should be no remarkable change

      Soldering Temperature: 235±5℃
      Immersion Duration: 2.5±0.5S
      Immersion Duration: 25±6mm/s

      Soldering    Heat Resistance

      Apperance

      Should    be no remarkable change

      Preheat Temperature:100~120℃
      Preheat Duration:60 Sec. max
      Temperature Increase by 2℃/sec. max
      Soldering Temperature:+260±5℃
      Immersion    Duration: 10±0.5Sec
      Immersion depth: 4±0.8mm from the roots
      After    test,allow it stay alone for 24±2 Hours
      at standard temperature and humidity before    making measurement

      Capacitance    Change Rate(△C/C)

      ±10% (Y5P)
      ±15%(Y5U )
      ±20%(Y5V )

      Withstand    Voltage
      (Between    Terminals)

      Shall    satisfy withstand voltage

      DissipationFactor

      ≤250×10-4 (1±0.2KHz,1.0±0.2 Vrms,20±2℃)

      Insulation    Resistance

      ≥5000 MΩ(500V 60Sec,20±2℃)

      Humidity    Heat Resistance

      Apperance

      Should    be no remarkable change

      Temperature: 40±2℃
      Humidity: 90~95%RH
      Storage Duration:500+24Hours
      After    test,allow it stay alone for 1~2 Hrs
      at standard temperature and humidity before    making measurement

      Capacitance    Change Rate(△C/C)

      ±10% (Y5P)
      ±15%(Y5U )
      ±20%(Y5V )

      Withstand    Voltage
           (Between    Terminals)

      Shall    satisfy withstand voltage

      DissipationFactor

      ≤5.0×10-4  (Y5P、Y5U)
      ≤7.5×10-4    (Y5V)
      (1±0.2KHz,1.0±0.2    Vrms,20±2℃)

      Insulation    Resistance

      ≥5000 MΩ(500V 60Sec,20±2℃)

      項目

      性能要求

      試驗方法

      耐久性試驗

      先施加三次脈沖如下:

      three.jpg                

      外觀

      無可見的損傷或異常

      溫度:85±3℃40±2℃下施加負載:50Hz/60Hz 425 Vrms (Y2) or 680Vrms(Y1)
      持續時間:1000小時
      并每小時將電壓升高到1000VAC,持續時間0.1s。。
      試驗后處理:
      電容器置于標準大氣壓條件下放置24±2小時后再進行測量

      容量變化率

      ±20%

      耐電壓
      (引線之間)

      符合耐電壓規定

      損耗角正切

      ≤5.0×10-4  (Y5P、Y5U)
      ≤7.5×10-4    (Y5V)
      (1±0.2KHz,1.0±0.2 Vrms,20±2℃)

      絕緣阻抗

      ≥5000 MΩ(500V60秒,20±2℃)

      Item

      Performance

      Test     Method

      Long Life Testing

      Pre-Loading    3 times to the capacitor by puls voltage

      three.jpg                

      Apperance

      Should    be no remarkable change

      Temperature:85±3℃40±2℃
      Voltage Loading: 425 Vrms (Y2) or 680Vrms(Y1) 50Hz/60Hz
      Duration:1000    Hrs AC Voltage up to1000V ,
      Consistance    time:0.1sec
      After test,allow it stay alone for    24±2Hrs at standard temperature and humidity before making measurement

      Capacitance    Change Rate(△C/C)

      ±20%

      Withstand    Voltage
       (Between    Terminals)

      Shall    satisfy withstand voltage

      DissipationFactor

      ≤5.0×10-4  (Y5P、Y5U)
      ≤7.5×10-4    (Y5V)
       (1±0.2KHz,1.0±0.2 Vrms,20±2℃)

      Insulation Resistance

      ≥5000 MΩ(500V60sec,20±2℃)

       

      国产精品又黄又爽又色无遮挡网站_一本二本人妻高清无码_无码动漫在线看明星_一二三区无码在线视频
    2. <strong id="n7php"></strong>

      <ruby id="n7php"></ruby>
        <i id="n7php"></i>
      1. <font id="n7php"></font>